Writing tips and writing guidelines for students,case study samples, admission essay examples, book reviews, paper writing tips, college essays, research proposal samples
Monday, 14 January 2019
Cream Seperation
Separation of solve from sufficient unction take out apply the Disc- Bowl Centrifuge. Introduction- bat is normally a dairy product containing high plump down percent, which can be seen floating on the top before the homogenization serve up. When the milk is unhomogenized, overtime, the plop igniter in weight rises to the top. The process in the industries is completely distinguishable as they use centrifuges, normally called as separators to accele ordain the skittering process. Cost of lap up totally depends upon its fat satiate. skim over usually produced by the livestock grazing process on natural pastures normally contains some amount of natural carotenoid pigments acquired from imbed materials they consume as a result of which the cream appears a trash yellowish in colour. Cream derived from the milk of livestock fed at heart is usually white in colour as they normally atomic number 18 grain based pellets. There is a formula for determining the rate of bank de posit, widely known as Stokes law. It states that a mote moving done viscous liquid attains a constant velocity or sedimentation rate. Equation for Stokes law Vg = d2 (Pp- P1)/ 18 ?G Where- Vg = Sedimentation Velocity d2 = particle Diameter Pp = Particle density P1 = Liquid density G = gravitative acceleration = viscosity of liquid Aims- 1. To separate cream from full cream milk at two focal ratio associationtings of the disc paradiddle centrifuge. 2. To prise sensory properties of the cream and skip overmed milk. 3. To determine the doneput of the centrifuge. Materials and Equipments- Disc-bowl centrifuge 1 lambert and 400 ml beakers Litre measuring cylinder Sample cups plain 2 Litres full cream milk Large Plastic lawn bowling Pans Stopwatch Digital Thermometer Method- 1.Two batches of 1 litre of full cream milk was warmed at 37 degree C. 2. 1 litre beaker was placed beneath the lower, heavy phase, spout of the centrifuge. This usually was the insinuate from where th e skim milk exits. Right after whence the 400 ml beaker was placed beneath the upper, light phase, spout of the centrifuge which usually was the exit point for the cream. 3. Before carrying out the next step, it was ensured that the tap of the milk receiving reservoir at the top of the centrifuge was in a closed position ie. Pointing N to S 4. Warmed milk weighing 1 litre was then(prenominal) inserted into the reservoir. . The motor was switched on as soon as milk was inserted and was set on the lowest zipper orbit by adjusting the speed reach knob. 6. As the motor speed was steady, the tap of the reservoir containing milk was then released and the stopwatch was started. 7. Portions at light and heavy liquid phases were then hive away from the relevant spouts, cream and plane milk respectively. 8. The stopwatch was switched off as soon as the milk reservoir was empty and the time taken was noted. 9. The motor of the centrifuge was allowed to run till the flow of skim milk a nd cream was ceased. 10.The portions of skimmed milk and cream received through their recounting phases were then measured and then the yield was calculated. 11. The throughput of the material was then resolute in litres per hour at its respective speed setting. 12. The stages 2 to 12 were repeated using second batch of warmed milk, with the only battle being the time setting. The complete process was carried out by operating(a) the motor on the highest speed setting. 13. The above process was followed by placing the rotund bowl underneath the spouts and by flushing the centrifuge using cold piss just to clear the washings in the centrifuge. 4. Right after the process the whole equipment was dismantled including the reservoirs spouts, collecting funnel etc. The parts were then process using hot water with a little detergent. 15. The cream and skimmed milk from each speed setting (i. e. High speed setting and low speed setting) were then subjected to sensory properties evaluat ion. * * * * Result- * * The following were the results obtained - 1. The results for 0. 1 % skimmed milk at low speed setting were * plentiful- 00. 07% * * And the results for same product at high speed setting were * blue-00. 03% * 2.The results for 2 % semi skimmed milk at low speed setting were * fill out- 1. 60 % * * The results for 2 % semi skimmed milk at high speed setting were * Fat- 1. 64% * 3. The results for 4% Whole milk at low speed setting were * Fat- 6. 56% * * The results for 4% Whole milk at High speed setting were * Fat- 7. 25% * * * Discussion- * 1. Principles of the operation of Disc-bowl Centrifuge. * Brennan (2006) states that the Disc bowl centrifuge works on the principle of particle density. Feed is introduced through the bottom of the bowl.As it comes with the contact of the centrifugal force, the dense phase moves downside while the lighter phase passes through the top spout. * 2. Different Categories of cream on tap(predicate) to the consumer and the ir profound minimum fat fields? * Sheila (2006) mentioned in an article that categories of cream available are * Single cream 18 % minimum fat content * Double cream 48% minimum fat content * half(prenominal) cream 12% minimum fat content * Whipping Cream 35% minimum fat content * Creme fraiche 30% minimum fat content * Soured cream 18% minimum fat content * Clotted cream 55% minimum fat content. 3. Categories of cream produced in the Practical? * Type of cream produced in the practical was single cream * 4. Purpose of Cream screw? * The thickness of the cream can be adjusted by the help of the cream screw. Cream screw helps to muddle the cream and helps the cream to let out. * * 5. Why is the milk heated first off? * De (1991) explained that, higher the temperature and degree during agitation the greater is the loss of skimmed milk and vice versa. When the milk is heated and agitated, the agitation process causes size decrement of bigger fat globules into smaller ones. As a result of which they escape the exercise of centrifugal force, leading to exclusion of fat loss in the skimmed milk. To reduce creaming. * * Conclusion- * Cream was successfully separated from the milk using Disc bowl centrifuge. The cream was further tested for its sensory properties, and the sensory properties of the cream were found to be appealing. * * * * References- * * J. G. Brennan (2006). Food Processing Handbook. Wiley-Vch. * * Sheila (2006). Cream Final Edition. The Times, London, UK. * * Sukumar De (1991). Outlines of Dairy Technology. Oxford University Press.
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment